How to Prepare Your Fireplace and Heating System for Winter
Before you light that first fire of the season, run through this checklist. A few simple steps now prevent the problems that show up at the worst possible time.
The first cold snap of the season has a way of making people want to light a fire immediately. Before you do, take 20 minutes to run through this checklist. The problems that cause chimney fires and carbon monoxide incidents almost always develop during the off-season — and a few simple checks before the first fire can prevent a very bad night.
For Wood-Burning Fireplaces
✅ Schedule your annual cleaning and inspection
If you have not had your chimney cleaned and inspected this year, do it before you use the fireplace. Creosote accumulates every season, and a chimney that went all summer without being cleaned has had months for animals to nest and debris to accumulate.
Annual cleaning is not optional — it is the single most important thing you can do to prevent a chimney fire. See our post on how often you should have your chimney swept for the full explanation.
✅ Check the damper
Open the damper and look up into the flue with a flashlight. You should see daylight at the top. If you see a blockage — a nest, debris, or a stuck damper plate — do not use the fireplace until it is cleared.
Test the damper operation: it should open and close smoothly and seal fully when closed. A damper that does not seal properly wastes heat all winter. A damper that does not open fully restricts draft and causes smoke to back up into the room.
✅ Inspect the firebox
Look at the firebox walls and floor. Cracks in the refractory panels (the panels lining the firebox interior) should be evaluated before use — small hairline cracks may be acceptable, but larger cracks or missing sections are a repair item. Check that the smoke shelf is clear of debris.
✅ Check the chimney cap
Look at the top of the chimney from the ground or a window. The chimney cap should be present and intact. A missing or damaged cap means rain and animals have had unrestricted access to the flue all summer. If the cap is missing, schedule a service call before using the fireplace.
✅ Stock the right wood
Only burn dry, seasoned hardwood — wood that has been split and dried for at least six months to a year. Burning green (unseasoned) wood produces significantly more creosote and smoke. Good choices for Bucks County: oak, maple, cherry, ash, and hickory.
Never burn treated lumber, painted wood, cardboard, or trash. These produce toxic gases and accelerate creosote buildup.
✅ Test your smoke and CO detectors
Before the first fire of the season, test every smoke detector and carbon monoxide detector in the house. Replace batteries if needed. If any detector is more than 7 years old (smoke) or 5 years old (CO), replace the unit.
For Gas Fireplaces
✅ Schedule an annual inspection
Gas fireplaces do not produce creosote, but they do produce combustion gases that must be safely vented. The venting system requires annual inspection — a blocked or failed gas fireplace vent is a carbon monoxide risk. See our post on carbon monoxide and your heating system for the full explanation.
✅ Clean the glass and burner
Gas fireplace glass gets coated with a white haze from combustion byproducts over time. Clean it with a fireplace glass cleaner (not standard glass cleaner — it can damage the glass coating). Inspect the ceramic logs or media for cracks or displacement and reposition them according to the manufacturer's instructions if needed.
✅ Check the pilot light and ignition
If your gas fireplace has a standing pilot light, verify it is lit before the heating season. If it has an electronic ignition, test it. If the ignition fails or the pilot will not stay lit, have it serviced before use.
✅ Inspect the vent termination
If you can safely see the exterior vent termination (the cap where the vent exits the house), check that it is clear of debris, bird nests, and vegetation. A blocked vent termination is a direct CO risk.
For Gas and Oil Furnaces and Boilers
✅ Schedule annual service
Your gas or oil heating system should be serviced annually by a qualified technician. This includes cleaning the burner, checking the heat exchanger, testing combustion efficiency, and inspecting the venting system.
The flue serving your furnace or boiler also requires annual inspection. If it vents through a masonry chimney, that chimney should be inspected as part of your annual chimney service. For oil systems, the flue should be cleaned annually as well.
✅ Replace the air filter
A clogged air filter restricts airflow, reduces efficiency, and can cause the heat exchanger to overheat. Replace it at the start of the heating season and every 1–3 months during the season depending on your filter type.
✅ Test the thermostat
Turn the thermostat to heat mode and set it above the current room temperature. The system should start within a few minutes. If it does not, check the circuit breaker and the system's power switch before calling for service.
✅ Check CO detectors near the furnace
Install a carbon monoxide detector within 10 feet of the furnace or boiler if you do not already have one. Test it. This is your last line of defense if the venting system fails.
The One Thing That Covers Everything
Most of the items on this checklist — the flue inspection, the chimney cap check, the venting assessment — are covered in a single professional chimney inspection. If you want to start the heating season with confidence, scheduling that inspection is the most efficient thing you can do.
Aspen Chimney Service is available seven days a week, 8 AM to 8 PM. Our inspection fee is $150 flat. We serve all of Bucks County — Levittown, Langhorne, Newtown, Doylestown, Warminster, Horsham, Hatboro, and surrounding communities.
Call (215) 771-5034 or book online.
Related reading: Carbon monoxide and your heating system · When is the best time to schedule a chimney sweep? · How often should you have your chimney swept?
Explore Topics
Written by
Aspen Chimney Service
Content creator and writer sharing insights and stories.